Jump to content
APC Forum

Recommended Posts

Posted
Good gravy! That was one beautiful shell BJV! How did you do your comets?
Posted

Good gravy! That was one beautiful shell BJV! How did you do your comets?

 

Dagabu here is a photo of the shell.

BJV

post-10172-0-94912000-1301243199_thumb.jpg

Posted (edited)
I am just guessing here so correct me if I am wrong but the comets have their own guns that they are propelled from? And each have a time fuse on them for timing? I'll take two cases please ;) Edited by dagabu
Posted
very nice!what composition did you use?
Posted

very nice!what composition did you use?

 

pyrogeorge here is the formula for the silver stars in my shell.

This is a very easy formula to roll by the way.

BJV

 

KNO3 45

Dark Alum 30

Atomized Alum 200mesh 10

Sulphur 10

Meal Powder 5

Dextrin +5

Posted

...here is a photo of the shell.

 

Did you time-fuse the comets seperately or just run some fuse through the lot?

Posted

Did you time-fuse the comets seperately or just run some fuse through the lot?

 

boule I used time fuse in each set of comets.

BJV

Posted

great job!

iv'e been toying with these and will test one tommorow. [the comets] one question that troubles me, is it just a bp sandwich or are there any other components as mine rattle a bit and it worries me they wont travel to my shoot site too well

probably just me worrying too much but i like evrything tight :wacko:

Posted

great job!

iv'e been toying with these and will test one tommorow. [the comets] one question that troubles me, is it just a bp sandwich or are there any other components as mine rattle a bit and it worries me they wont travel to my shoot site too well

probably just me worrying too much but i like evrything tight :wacko:

 

dan999ification,

The comet tubes I used are 2 1/2" x 1" . The comets 1" x 3/4". I use about 2grams of 4f g between the two comets.

Hope this answers your question.

BJV

Posted

dan999ification,

The comet tubes I used are 2 1/2" x 1" . The comets 1" x 3/4". I use about 2grams of 4f g between the two comets.

Hope this answers your question.

BJV

yes and thanks, my tubes are too long :whistle:
Posted

dan999ification,

The comet tubes I used are 2 1/2" x 1" . The comets 1" x 3/4". I use about 2grams of 4f g between the two comets.

Hope this answers your question.

BJV

 

Thanks BJV, I may just try that on a rocket some day. ;)

Posted
Very nice rising effects BJV ! These rising effects create such a nice tension before the break, as opposed to just a big rising comet. Break is also nice.
Posted
Do the time fuse from the ascending split comets light well enough from just the lift gasses?
Posted
Great shell! I like all your work, you really put labor into it.
Posted
What is the red stuff on your timefuse? Nice shell :)!
Posted

Do the time fuse from the ascending split comets light well enough from just the lift gasses?

Mumbles the time fuse is cross matched with thermalite, I cross match all my time fuse with it.

BJV

Posted

What is the red stuff on your timefuse? Nice shell :)!

ExplosiveCoek I cover the cross match time fuse with tissue paper. It's just to protect the shell from a stray spark.

BJV

  • 2 months later...
Posted
Very Very nice well done
Posted

I've been so busy with so many things I missed this thread, and for a long time no doubt. Anyway, great job BJV! Each effect took fire and was clearly seen.

 

Mark

Posted
man that was a beautiful shell so nice I just had to watch the video a second time
Posted

man that was a beautiful shell so nice I just had to watch the video a second time

Thanks Ralph

BJV

×
×
  • Create New...