fckiamdead Posted January 4, 2018 Author Posted January 4, 2018 Time to move on to 5". I shot some 6 inch but they went very high so the clouds took em ;(I have a film whit one where i did a huge misstake... i put Independence red stars (ring) along whit a streamer effect.. you can only see the red in the clouds/mist. Very dumb decision Here´s some more 3 inch...
rogeryermaw Posted January 4, 2018 Posted January 4, 2018 man! some fine work in these shells! crisp color changes, multiple effects and all crammed in 3 and 4 inch shells...that was impressive
burningRNX Posted January 4, 2018 Posted January 4, 2018 Verry Nice shells F*Imdead!, its amazing to see that much effect in 3" How did you screen them? did you dry them before screening? or did you roll them to the size / screening them between increments?Compositions?layer thickness of collor?total star diameter?
calebkessinger Posted January 5, 2018 Posted January 5, 2018 Some people just "got it" what a show man.
fckiamdead Posted January 5, 2018 Author Posted January 5, 2018 (edited) Verry Nice shells F*Imdead!, its amazing to see that much effect in 3" How did you screen them? did you dry them before screening? or did you roll them to the size / screening them between increments?Compositions?layer thickness of collor?total star diameter?HelloThanks I use a small lead core to roll on. Sort them whit this homemade good looking device (roll maybe 3mm each time then dry and repeat)The latest film is Spanish fuschia and plain BP meal whit 10% FeTi, very thin layer of BP+si prime. ( I always use a very thin layer of prime to get more composition place) The one to the left is Fuschia and the other one is the blue/Red from a video in this thread.Couldn´t break them 100% in half.. Edited January 5, 2018 by fckiamdead 1
fckiamdead Posted April 1, 2018 Author Posted April 1, 2018 An attempt to make a cylinder shell whit timed reports. 3pc of timed rising effects. BP/FeTi "ring" 1
dynomike1 Posted April 1, 2018 Posted April 1, 2018 I cant ever get my inserts to go off at the same time.
fckiamdead Posted April 2, 2018 Author Posted April 2, 2018 I cant ever get my inserts to go off at the same time.I made a time fuse cutter, works great!
dynomike1 Posted April 2, 2018 Posted April 2, 2018 I have a fuse cutter and still cant get em to go off at the same time.
MrB Posted April 3, 2018 Posted April 3, 2018 I use a cutter, and have done both punched through timefuse, with a strand of BM in the hole, dipped i NC / BP slurry, and tied, bent over the end, BM. For me, no doubt the best results were with punched hole for the BM, followed by NC / BP slurry, and last... well. It's just down to how consistent you can be, and that of course also applies to the timefuse. If it isn't consistent, then nothing else will be either.
rocketmaster Posted April 20, 2018 Posted April 20, 2018 @fckiamdead what sort of machine are you using to roll your stars? Picture?
fckiamdead Posted April 21, 2018 Author Posted April 21, 2018 @fckiamdead what sort of machine are you using to roll your stars? Picture?HelloI can take some pictures tomorrow for you. Regards
fckiamdead Posted September 26, 2018 Author Posted September 26, 2018 An attempt on making a red horsetail cylinder "smoke" shell Yes there is a tail...but kind of small one.. the bang was nice though... you have to start somewhere...
Recommended Posts